Non-return-to-zero
This article needs additional citations for verification. (June 2023) |
![](http://upload.wikimedia.org/wikipedia/commons/5/55/NRZcode.png)
In telecommunications, a non-return-to-zero (NRZ) line code is a binary code in which ones are represented by one significant condition, usually a positive voltage, while zeros are represented by some other significant condition, usually a negative voltage, with no other neutral or rest condition.
For a given data signaling rate, i.e., bit rate, the NRZ code requires only half the baseband bandwidth required by the Manchester code (the passband bandwidth is the same). The pulses in NRZ have more energy than a return-to-zero (RZ) code, which also has an additional rest state beside the conditions for ones and zeros.
When used to represent data in an asynchronous communication scheme, the absence of a neutral state requires other mechanisms for bit synchronization when a separate clock signal is not available. Since NRZ is not inherently a self-clocking signal, some additional synchronization technique must be used for avoiding bit slips; examples of such techniques are a run-length-limited constraint and a parallel synchronization signal.
Variants
[edit]NRZ can refer to any of the following serializer line codes:
Code name |
Alternate name |
Complete name | Description |
---|---|---|---|
NRZ(L) | NRZL | Non-return-to-zero level | Appears as raw binary bits without any coding. Typically binary 1 maps to logic-level high, and binary 0 maps to logic-level low. Inverse logic mapping is also a type of NRZ(L) code. |
NRZ(I) | NRZI | Non-return-to-zero inverted | Refers to either an NRZ(M) or NRZ(S) code. |
NRZ(M) | NRZM | Non-return-to-zero mark | Serializer mapping {0: constant, 1: toggle}. |
NRZ(S) | NRZS | Non-return-to-zero space | Serializer mapping {0: toggle, 1: constant}. |
NRZ(C) | NRZC | Non-return-to-zero change |
The NRZ code also can be classified as a polar or non-polar, where polar refers to a mapping to voltages of +V and −V, and non-polar refers to a voltage mapping of +V and 0, for the corresponding binary values of 0 and 1.
Unipolar non-return-to-zero level
[edit]![](http://upload.wikimedia.org/wikipedia/commons/2/23/Nrz-lb.gif)
"One" is represented by a DC bias on the transmission line (conventionally positive), while "zero" is represented by the absence of bias – the line at 0 volts or grounded. For this reason it is also known as "on-off keying". In clock language, a "one" transitions to or remains at a biased level on the trailing clock edge of the previous bit, while "zero" transitions to or remains at no bias on the trailing clock edge of the previous bit. Among the disadvantages of unipolar NRZ is that it allows for long series without change, which makes synchronization difficult, although this is not unique to the unipolar case. One solution is to not send bytes without transitions. More critically, and unique to unipolar NRZ, are issues related to the presence of a transmitted DC level – the power spectrum of the transmitted signal does not approach zero at zero frequency. This leads to two significant problems: first, the transmitted DC power leads to higher power losses than other encodings, and second, the presence of a DC signal component requires that the transmission line be DC-coupled.
Bipolar non-return-to-zero level
[edit]"One" is represented by one physical level (usually a positive voltage), while "zero" is represented by another level (usually a negative voltage). In clock language, in bipolar NRZ-level the voltage "swings" from positive to negative on the trailing edge of the previous bit clock cycle.
An example of this is RS-232, where "one" is −12 V to −5 V and "zero" is +5 V to +12 V.
Non-return-to-zero space
[edit]![](http://upload.wikimedia.org/wikipedia/commons/6/66/Nrz-s.gif)
![](http://upload.wikimedia.org/wikipedia/commons/thumb/d/d3/Nrzi_encoder_2.svg/220px-Nrzi_encoder_2.svg.png)
"One" is represented by no change in physical level, while "zero" is represented by a change in physical level. In clock language, the level transitions on the trailing clock edge of the previous bit to represent a "zero".
This "change-on-zero" is used by High-Level Data Link Control and USB. They both avoid long periods of no transitions (even when the data contains long sequences of 1 bits) by using zero-bit insertion. HDLC transmitters insert a 0 bit after 5 contiguous 1 bits (except when transmitting the frame delimiter "01111110"). USB transmitters insert a 0 bit after 6 consecutive 1 bits. The receiver at the far end uses every transition — both from 0 bits in the data and these extra non-data 0 bits — to maintain clock synchronization. The receiver otherwise ignores these non-data 0 bits.
Non-return-to-zero inverted
[edit]![](http://upload.wikimedia.org/wikipedia/commons/e/e4/NRZI_example.png)
![](http://upload.wikimedia.org/wikipedia/commons/b/bc/Nrz-i.gif)
![](http://upload.wikimedia.org/wikipedia/commons/thumb/d/dd/Nrzi_encoder.svg/220px-Nrzi_encoder.svg.png)
Non-return-to-zero, inverted (NRZI, also known as non-return to zero IBM,[1] inhibit code,[2] or IBM code[2]) was devised by Bryon E. Phelps (IBM) in 1956.[2][3] It is a method of mapping a binary signal to a physical signal for transmission over some transmission medium. The two-level NRZI signal distinguishes data bits by the presence or absence of a transition at a clock boundary. The NRZI encoded signal can be decoded unambiguously after passing through a data path that doesn’t preserve polarity.
Which bit value corresponds to a transition varies in practice, NRZI applies equally to both. Magnetic storage generally uses the NRZ-M, non-return-to-zero mark convention: a logical 1 is encoded as a transition, and a logical 0 is encoded as no transition. The HDLC and Universal Serial Bus protocols use the opposite NRZ-S, non-return-to-zero space convention: a logical 0 is a transition, and a logical 1 is no transition. Neither NRZI encoding guarantees that the encoded bitstream has transitions.
An asynchronous receiver uses an independent bit clock that is phase synchronized by detecting bit transitions. When an asynchronous receiver decodes a block of bits without a transition longer than the period of the difference between the frequency of the transmitting and receiving bit clocks, the decoder’s bit clock is either 1 bit earlier than the encoder resulting in a duplicated bit being inserted in the decoded data stream, or the decoder’s bit clock is 1 bit later than the encoder resulting in a duplicated bit being removed from the decoded data stream. Both are referred to as “bit slip” denoting that the phase of the bit clock has slipped a bit period.
Forcing transitions at intervals shorter than the bit clock difference period allows an asynchronous receiver to be used for NRZI bit streams. Additional transitions necessarily consume some of the data channel’s rate capacity. Consuming no more of the channel capacity than necessary to maintain bit clock synchronization without increasing costs related to complexity is a problem with many possible solutions.
Run-length limited (RLL) encodings have been used for magnetic disk and tape storage devices using fixed-rate RLL codes that increase the channel data rate by a known fraction of the information data rate. HDLC and USB use bit stuffing: inserting an additional 0 bit before NRZ-S encoding to force a transition in the encoded data sequence after 5 (HLDC) or 6 (USB) consecutive 1 bits. Bit stuffing consumes channel capacity only when necessary but results in a variable information data rate.
Synchronized non-return-to-zero
[edit]Synchronized NRZI (SNRZI) and group-coded recording (GCR) are modified forms of NRZI.[4] In SNRZI-M each 8-bit group is extended to 9 bits by a 1 in order to insert a transition for synchronisation.[4]
Comparison with return-to-zero
[edit]Return-to-zero describes a line code used in telecommunications in which the signal drops (returns) to zero between each pulse. This takes place even if a number of consecutive 0s or 1s occur in the signal. The signal is self-clocking. This means that a separate clock does not need to be sent alongside the signal, but suffers from using twice the bandwidth to achieve the same data-rate as compared to non-return-to-zero format.
The zero between each bit is a neutral or rest condition, such as a zero amplitude in pulse-amplitude modulation (PAM), zero phase shift in phase-shift keying (PSK), or mid-frequency in frequency-shift keying (FSK). That zero condition is typically halfway between the significant condition representing a 1 bit and the other significant condition representing a 0 bit.
Although return-to-zero contains a provision for synchronization, it still may have a DC component resulting in baseline wander during long strings of 0 or 1 bits, just like the line code non-return-to-zero.
See also
[edit]![](http://upload.wikimedia.org/wikipedia/en/thumb/4/4a/Commons-logo.svg/30px-Commons-logo.svg.png)
References
[edit]- ^ IBM 729 II, IV, V, VI Magnetic Tape Units (PDF) (223-6988 ed.). 1962. p. 7. Archived (PDF) from the original on 2022-10-09. Retrieved 12 February 2018.
- ^ a b c Palmer, Dean (2005). "Section 1: Recording Systems, 1: A brief history of magnetic recording". In Vasic, Bane; Kurtas, Erozan M. (eds.). Coding and Signal Processing for Magnetic Recording Systems (1st ed.). CRC Press. pp. I-6, I-15. ISBN 0-8493-1524-7.
- ^ US 2774646, Phelps, Bryon E., "Magnetic recording method", published 1956-12-18, assigned to IBM [1] (See also: DE950858C)
- ^ a b Patel, Arvind Motibhai (1988). "5. Signal and Error-Control Coding". In Mee, C. Denis; Daniel, Eric D. (eds.). Magnetic Recording. Vol. II: Computer Data Storage (1st ed.). McGraw-Hill Book Company. ISBN 0-07-041272-3.
Further reading
[edit]- Brey, Barry (2006). The Intel Microprocessors. Columbus: Pearson Prentice Hall. ISBN 0-13-119506-9.
- Savard, John J. G. (2018) [2006]. "Digital Magnetic Tape Recording". quadibloc. Archived from the original on 2018-07-02. Retrieved 2018-07-16.
- Watkinson, John (1990). "3.7. Randomized NRZ". Coding for Digital Recording. Stoneham, MA, USA: Focal Press. pp. 64–65. ISBN 0-240-51293-6. ISBN 978-0-240-51293-8.
- Mahmoud, A. A., Ahmed, M. (2014), Comparative study on modulation dynamic characteristics of laser diodes using RZ and NRZ bit formats, International Journal of Numerical Modelling: Electronic Networks, Devices and Fields, pp. 138-152.
{{citation}}
: CS1 maint: multiple names: authors list (link) https://onlinelibrary.wiley.com/doi/full/10.1002/jnm.1905
External links
[edit] This article incorporates public domain material from Federal Standard 1037C. General Services Administration. Archived from the original on 2022-01-22. (in support of MIL-STD-188).