Jump to content

Tunnel magnetoresistance

From Wikipedia, the free encyclopedia
Magnetic tunnel junction (schematic)

Tunnel magnetoresistance (TMR) is a magnetoresistive effect that occurs in a magnetic tunnel junction (MTJ), which is a component consisting of two ferromagnets separated by a thin insulator. If the insulating layer is thin enough (typically a few nanometres), electrons can tunnel from one ferromagnet into the other. Since this process is forbidden in classical physics, the tunnel magnetoresistance is a strictly quantum mechanical phenomenon, and lies in the study of spintronics.

Magnetic tunnel junctions are manufactured in thin film technology. On an industrial scale the film deposition is done by magnetron sputter deposition; on a laboratory scale molecular beam epitaxy, pulsed laser deposition and electron beam physical vapor deposition are also utilized. The junctions are prepared by photolithography.

Phenomenological description

[edit]

The direction of the two magnetizations of the ferromagnetic films can be switched individually by an external magnetic field. If the magnetizations are in a parallel orientation it is more likely that electrons will tunnel through the insulating film than if they are in the oppositional (antiparallel) orientation. Consequently, such a junction can be switched between two states of electrical resistance, one with low and one with very high resistance.

History

[edit]

The effect was originally discovered in 1975 by Michel Jullière (University of Rennes, France) in Fe/Ge-O/Co-junctions at 4.2 K. The relative change of resistance was around 14%, and did not attract much attention.[1] In 1991 Terunobu Miyazaki (Tohoku University, Japan) found a change of 2.7% at room temperature. Later, in 1994, Miyazaki found 18% in junctions of iron separated by an amorphous aluminum oxide insulator [2] and Jagadeesh Moodera found 11.8% in junctions with electrodes of CoFe and Co.[3] The highest effects observed at this time with aluminum oxide insulators was around 70% at room temperature.

Since the year 2000, tunnel barriers of crystalline magnesium oxide (MgO) have been under development. In 2001 Butler and Mathon independently made the theoretical prediction that using iron as the ferromagnet and MgO as the insulator, the tunnel magnetoresistance can reach several thousand percent.[4][5] The same year, Bowen et al. were the first to report experiments showing a significant TMR in a MgO based magnetic tunnel junction [Fe/MgO/FeCo(001)].[6] In 2004, Parkin and Yuasa were able to make Fe/MgO/Fe junctions that reach over 200% TMR at room temperature.[7][8] In 2008, effects of up to 604% at room temperature and more than 1100% at 4.2 K were observed in junctions of CoFeB/MgO/CoFeB by S. Ikeda, H. Ohno group of Tohoku University in Japan.[9]

Applications

[edit]

The read-heads of modern hard disk drives work on the basis of magnetic tunnel junctions. TMR, or more specifically the magnetic tunnel junction, is also the basis of MRAM, a new type of non-volatile memory. The 1st generation technologies relied on creating cross-point magnetic fields on each bit to write the data on it, although this approach has a scaling limit at around 90–130 nm.[10] There are two 2nd generation techniques currently being developed: Thermal Assisted Switching (TAS)[10] and Spin-transfer torque.

Magnetic tunnel junctions are also used for sensing applications. Today they are commonly used for position sensors and current sensors in various automotive, industrial and consumer applications. These higher performance sensors are replacing Hall sensors in many applications due to their improved performance.[11]

Physical explanation

[edit]
Two-current model for parallel and anti-parallel alignment of the magnetizations

The relative resistance change—or effect amplitude—is defined as

where is the electrical resistance in the anti-parallel state, whereas is the resistance in the parallel state.

The TMR effect was explained by Jullière with the spin polarizations of the ferromagnetic electrodes. The spin polarization P is calculated from the spin dependent density of states (DOS) at the Fermi energy:

The spin-up electrons are those with spin orientation parallel to the external magnetic field, whereas the spin-down electrons have anti-parallel alignment with the external field. The relative resistance change is now given by the spin polarizations of the two ferromagnets, P1 and P2:

If no voltage is applied to the junction, electrons tunnel in both directions with equal rates. With a bias voltage U, electrons tunnel preferentially to the positive electrode. With the assumption that spin is conserved during tunneling, the current can be described in a two-current model. The total current is split in two partial currents, one for the spin-up electrons and another for the spin-down electrons. These vary depending on the magnetic state of the junctions.

There are two possibilities to obtain a defined anti-parallel state. First, one can use ferromagnets with different coercivities (by using different materials or different film thicknesses). And second, one of the ferromagnets can be coupled with an antiferromagnet (exchange bias). In this case the magnetization of the uncoupled electrode remains "free".

The TMR becomes infinite if P1 and P2 equal 1, i.e. if both electrodes have 100% spin polarization. In this case the magnetic tunnel junction becomes a switch, that switches magnetically between low resistance and infinite resistance. Materials that come into consideration for this are called ferromagnetic half-metals. Their conduction electrons are fully spin-polarized. This property is theoretically predicted for a number of materials (e.g. CrO2, various Heusler alloys) but its experimental confirmation has been the subject of subtle debate. Nevertheless, if one considers only those electrons that enter into transport, measurements by Bowen et al. of up to 99.6%[12] spin polarization at the interface between La0.7Sr0.3MnO3 and SrTiO3 pragmatically amount to experimental proof of this property.

The TMR decreases with both increasing temperature and increasing bias voltage. Both can be understood in principle by magnon excitations and interactions with magnons, as well as due to tunnelling with respect to localized states induced by oxygen vacancies (see Symmetry Filtering section hereafter).[13]

Symmetry-filtering in tunnel barriers

[edit]

Prior to the introduction of epitaxial magnesium oxide (MgO), amorphous aluminum oxide was used as the tunnel barrier of the MTJ, and typical room temperature TMR was in the range of tens of percent. MgO barriers increased TMR to hundreds of percent. This large increase reflects a synergetic combination of electrode and barrier electronic structures, which in turn reflects the achievement of structurally ordered junctions. Indeed, MgO filters the tunneling transmission of electrons with a particular symmetry that are fully spin-polarized within the current flowing across body-centered cubic Fe-based electrodes. Thus, in the MTJ's parallel (P) state of electrode magnetization, electrons of this symmetry dominate the junction current. In contrast, in the MTJ's antiparallel (AP) state, this channel is blocked, such that electrons with the next most favorable symmetry to transmit dominate the junction current. Since those electrons tunnel with respect to a larger barrier height, this results in the sizeable TMR.

Beyond these large values of TMR across MgO-based MTJs,[9] this impact of the barrier's electronic structure on tunnelling spintronics has been indirectly confirmed by engineering the junction's potential landscape for electrons of a given symmetry. This was first achieved by examining how the electrons of a lanthanum strontium manganite half-metallic electrode with both full spin (P=+1 [12]) and symmetry polarization tunnel across an electrically biased SrTiO3 tunnel barrier.[14] The conceptually simpler experiment of inserting an appropriate metal spacer at the junction interface during sample growth was also later demonstrated[15][16] .

While theory, first formulated in 2001,[4][5] predicts large TMR values associated with a 4eV barrier height in the MTJ's P state and 12eV in the MTJ's AP state, experiments reveal barrier heights as low as 0.4eV.[7] This contradiction is lifted if one takes into account the localized states of oxygen vacancies in the MgO tunnel barrier. Extensive solid-state tunnelling spectroscopy experiments across MgO MTJs revealed in 2014[13] that the electronic retention on the ground and excited states of an oxygen vacancy, which is temperature-dependent, determines the tunnelling barrier height for electrons of a given symmetry, and thus crafts the effective TMR ratio and its temperature dependence. This low barrier height in turn enables the high current densities required for spin-transfer torque, discussed hereafter.

Spin-transfer torque in magnetic tunnel junctions (MTJs)

[edit]

The effect of spin-transfer torque has been studied and applied widely in MTJs, where there is a tunnelling barrier sandwiched between a set of two ferromagnetic electrodes such that there is (free) magnetization of the right electrode, while assuming that the left electrode (with fixed magnetization) acts as spin-polarizer. This may then be pinned to some selecting transistor in a magnetoresistive random-access memory device, or connected to a preamplifier in a hard disk drive application.

The spin-transfer torque vector, driven by the linear response voltage, can be computed from the expectation value of the torque operator:

where is the gauge-invariant nonequilibrium density matrix for the steady-state transport, in the zero-temperature limit, in the linear-response regime,[17] and the torque operator is obtained from the time derivative of the spin operator:

Using the general form of a 1D tight-binding Hamiltonian:

where total magnetization (as macrospin) is along the unit vector and the Pauli matrices properties involving arbitrary classical vectors , given by

it is then possible to first obtain an analytical expression for (which can be expressed in compact form using , and the vector of Pauli spin matrices ).

The spin-transfer torque vector in general MTJs has two components: a parallel and perpendicular component:

A parallel component:

And a perpendicular component:

In symmetric MTJs (made of electrodes with the same geometry and exchange splitting), the spin-transfer torque vector has only one active component, as the perpendicular component disappears:

.[18]

Therefore, only vs. needs to be plotted at the site of the right electrode to characterise tunnelling in symmetric MTJs, making them appealing for production and characterisation at an industrial scale.

Note: In these calculations the active region (for which it is necessary to calculate the retarded Green's function) should consist of the tunnel barrier + the right ferromagnetic layer of finite thickness (as in realistic devices). The active region is attached to the left ferromagnetic electrode (modeled as semi-infinite tight-binding chain with non-zero Zeeman splitting) and the right N electrode (semi-infinite tight-binding chain without any Zeeman splitting), as encoded by the corresponding self-energy terms.

Discrepancy between theory and experiment

[edit]

Theoretical tunnelling magneto-resistance ratios of 10000%[19] have been predicted. However, the largest that have been observed are only 604%.[20] One suggestion is that grain boundaries could be affecting the insulating properties of the MgO barrier; however, the structure of films in buried stack structures is difficult to determine.[21] The grain boundaries may act as short circuit conduction paths through the material, reducing the resistance of the device. Recently, using new scanning transmission electron microscopy techniques, the grain boundaries within FeCoB/MgO/FeCoB MTJs have been atomically resolved. This has allowed first principles density functional theory calculations to be performed on structural units that are present in real films. Such calculations have shown that the band gap can be reduced by as much as 45%.[22]

In addition to grain boundaries, point defects such as boron interstitial and oxygen vacancies could be significantly altering the tunnelling magneto-resistance. Recent theoretical calculations have revealed that boron interstitials introduce defect states in the band gap potentially reducing the TMR further[23] These theoretical calculations have also been backed up by experimental evidence showing the nature of boron within the MgO layer between two different systems and how the TMR is different.[24]

See also

[edit]

References

[edit]
  1. ^ M. Julliere (1975). "Tunneling between ferromagnetic films". Phys. Lett. 54A (3): 225–6. Bibcode:1975PhLA...54..225J. doi:10.1016/0375-9601(75)90174-7.
  2. ^ T. Miyazaki & N. Tezuka (1995). "Giant magnetic tunneling effect in Fe/Al2O3/Fe junction". J. Magn. Magn. Mater. 139 (3): L231–4. Bibcode:1995JMMM..139L.231M. doi:10.1016/0304-8853(95)90001-2.
  3. ^ J. S. Moodera; et al. (1995). "Large Magnetoresistance at Room Temperature in Ferromagnetic Thin Film Tunnel Junctions". Phys. Rev. Lett. 74 (16): 3273–6. Bibcode:1995PhRvL..74.3273M. doi:10.1103/PhysRevLett.74.3273. PMID 10058155.
  4. ^ a b W. H. Butler; X.-G. Zhang; T. C. Schulthess & J. M. MacLaren (2001). "Spin-dependent tunneling conductance of Fe/MgO/Fe sandwiches". Phys. Rev. B. 63 (5): 054416. Bibcode:2001PhRvB..63e4416B. doi:10.1103/PhysRevB.63.054416.
  5. ^ a b J. Mathon & A. Umerski (2001). "Theory of tunneling magnetoresistance of an epitaxial Fe/MgO/Fe (001) junction". Phys. Rev. B. 63 (22): 220403. Bibcode:2001PhRvB..63v0403M. doi:10.1103/PhysRevB.63.220403.
  6. ^ M. Bowen; et al. (2001). "Large magnetoresistance in Fe/MgO/FeCo(001) epitaxial tunnel junctions on GaAs(001)" (PDF). Appl. Phys. Lett. 79 (11): 1655. Bibcode:2001ApPhL..79.1655B. doi:10.1063/1.1404125. hdl:2445/33761.
  7. ^ a b S Yuasa; T Nagahama; A Fukushima; Y Suzuki & K Ando (2004). "Giant room-temperature magnetoresistance in single-crystal Fe/MgO/Fe magnetic tunnel junctions". Nat. Mater. 3 (12): 868–871. Bibcode:2004NatMa...3..868Y. doi:10.1038/nmat1257. PMID 15516927. S2CID 44430045.
  8. ^ S. S. P. Parkin; et al. (2004). "Giant tunnelling magnetoresistance at room temperature with MgO (100) tunnel barriers". Nat. Mater. 3 (12): 862–7. Bibcode:2004NatMa...3..862P. doi:10.1038/nmat1256. PMID 15516928. S2CID 33709206.
  9. ^ a b Ikeda, S.; Hayakawa, J.; Ashizawa, Y.; Lee, Y. M.; Miura, K.; Hasegawa, H.; Tsunoda, M.; Matsukura, F.; Ohno, H. (25 August 2008). "Tunnel magnetoresistance of 604% at 300K by suppression of Ta diffusion in CoFeB/MgO/CoFeB pseudo-spin-valves annealed at high temperature". Applied Physics Letters. 93 (8): 082508. Bibcode:2008ApPhL..93h2508I. doi:10.1063/1.2976435. S2CID 122271110.
  10. ^ a b Barry Hoberman The Emergence of Practical MRAM Archived 2011-04-27 at the Wayback Machine. Crocus Technologies
  11. ^ "From Hall Effect to TMR" (PDF). Crocus Technology. Retrieved 22 March 2022.
  12. ^ a b Bowen, M; Barthélémy, A; Bibes, M; Jacquet, E; Contour, J P; Fert, A; Wortmann, D; Blügel, S (2005-10-19). "Half-metallicity proven using fully spin-polarized tunnelling". Journal of Physics: Condensed Matter. 17 (41): L407–9. Bibcode:2005JPCM...17L.407B. doi:10.1088/0953-8984/17/41/L02. ISSN 0953-8984. S2CID 117180760.
  13. ^ a b Schleicher, F.; Halisdemir, U.; Lacour, D.; Gallart, M.; Boukari, S.; Schmerber, G.; Davesne, V.; Panissod, P.; Halley, D.; Majjad, H.; Henry, Y.; Leconte, B.; Boulard, A.; Spor, D.; Beyer, N.; Kieber, C.; Sternitzky, E.; Cregut, O.; Ziegler, M.; Montaigne, F.; Beaurepaire, E.; Gilliot, P.; Hehn, M.; Bowen, M. (2014-08-04). "Localized states in advanced dielectrics from the vantage of spin- and symmetry-polarized tunnelling across MgO". Nature Communications. 5: 4547. Bibcode:2014NatCo...5.4547S. doi:10.1038/ncomms5547. ISSN 2041-1723. PMID 25088937.
  14. ^ Bowen, M.; Barthélémy, A.; Bellini, V.; Bibes, M.; Seneor, P.; Jacquet, E.; Contour, J.-P.; Dederichs, P. (April 2006). "Observation of Fowler–Nordheim hole tunneling across an electron tunnel junction due to total symmetry filtering". Physical Review B. 73 (14): 140408. Bibcode:2006PhRvB..73n0408B. doi:10.1103/PhysRevB.73.140408. ISSN 1098-0121.
  15. ^ Greullet, F.; Tiusan, C.; Montaigne, F.; Hehn, M.; Halley, D.; Bengone, O.; Bowen, M.; Weber, W. (November 2007). "Evidence of a Symmetry-Dependent Metallic Barrier in Fully Epitaxial MgO Based Magnetic Tunnel Junctions". Physical Review Letters. 99 (18): 187202. Bibcode:2007PhRvL..99r7202G. doi:10.1103/PhysRevLett.99.187202. ISSN 0031-9007. PMID 17995434. S2CID 30668262.
  16. ^ Matsumoto, Rie; Fukushima, Akio; Yakushiji, Kay; Nishioka, Shingo; Nagahama, Taro; Katayama, Toshikazu; Suzuki, Yoshishige; Ando, Koji; Yuasa, Shinji (2009). "Spin-dependent tunneling in epitaxial Fe/Cr/MgO/Fe magnetic tunnel junctions with an ultrathin Cr(001) spacer layer". Physical Review B. 79 (17): 174436. Bibcode:2009PhRvB..79q4436M. doi:10.1103/PhysRevB.79.174436.
  17. ^ Mahfouzi, F.; Nagaosa, N.; Nikolić, B.K. (2012). "Spin-Orbit Coupling Induced Spin-Transfer Torque and Current Polarization in Topological-Insulator/Ferromagnet Vertical Heterostructures". Phys. Rev. Lett. 109 (16): 166602 See Eq. 13. arXiv:1202.6602. Bibcode:2012PhRvL.109p6602M. doi:10.1103/PhysRevLett.109.166602. PMID 23215105. S2CID 40870461.
  18. ^ [S.-C. Oh et al., Bias-voltage dependence of perpendicular spin-transfer torque in a symmetric MgO-based magnetic tunnel junctions, Nature Phys. 5, 898 (2009). (PDF)
  19. ^ de Sousa, D. J. P.; Ascencio, C. O.; Haney, P. M.; Wang, J. P.; Low, Tony (2021-07-01). "Gigantic tunneling magnetoresistance in magnetic Weyl semimetal tunnel junctions". Physical Review B. 104 (4): 041401. arXiv:2103.05501. Bibcode:2021PhRvB.104d1401D. doi:10.1103/physrevb.104.l041401. ISSN 2469-9950. PMC 9982938. PMID 36875244. S2CID 232168454.
  20. ^ Ikeda, S.; Hayakawa, J.; Ashizawa, Y.; Lee, Y.M.; Miura, K.; Hasegawa, H.; et al. (2008). "Tunnel magnetoresistance of 604% at 300 K by suppression of Ta diffusion in CoFeBMgOCoFeB pseudo-spin-valves annealed at high temperature". Applied Physics Letters. 93 (8): 39–42. Bibcode:2008ApPhL..93h2508I. doi:10.1063/1.2976435. S2CID 122271110.
  21. ^ Benedetti, S.; Torelli, P.; Valeri, S.; Benia, H.M.; Nilius, N.; Renaud, G. (2008). "Structure and morphology of thin MgO films on Mo(001)". Physical Review B. 78 (19): 1–8. Bibcode:2008PhRvB..78s5411B. doi:10.1103/PhysRevB.78.195411. hdl:11858/00-001M-0000-0010-FF18-5.
  22. ^ Bean, J.J.; Saito, M.; Fukami, S.; Sato, H.; Ikeda, S. (2017). "Atomic structure and electronic properties of MgO grain boundaries in tunnelling magnetoresistive devices". Scientific Reports. 7: 1–9. Bibcode:2017NatSR...745594B. doi:10.1038/srep45594. PMC 5379487. PMID 28374755.
  23. ^ Bean, J.J.; McKenna, K.P. (2018). "Stability of point defects near MgO grain boundaries in FeCoB/MgO/FeCoB magnetic tunnel junctions" (PDF). Physical Review Materials. 2 (12): 125002. Bibcode:2018PhRvM...2l5002B. doi:10.1103/PhysRevMaterials.2.125002. S2CID 197631853.
  24. ^ Xu, X.D.; Mukaiyama, K.; Kasai, S.; Ohkubo, T.; Hono, K. (2018). "Impact of boron diffusion at MgO grain boundaries on magneto-transport properties of MgO/CoFeB/W magnetic tunnel junctions". Acta Materialia. 161: 360–6. Bibcode:2018AcMat.161..360X. doi:10.1016/j.actamat.2018.09.028. S2CID 140024466.